How To Fix Lawn Mower Pull Cord

ByKasia Nowick

The pull cord on your lawn mower is an essential part of the machine. If the cord is not working properly, the mower will not be able to start. There are a few things that you can do to fix a lawn mower pull cord.

  • If the pull cord on your lawn mower is stuck, you may be able to fix it without taking the mower to a repair shop
  • First, check the cord for any knots or tangles
  • If you find any, use a pair of scissors to cut them out
  • Next, inspect the cord for any fraying or wear
  • If the cord is damaged, you will need to replace it
  • If the cord is not damaged, try pulling it a few times to see if it will loosen up
  • If it does not, you may need to disassemble the mower to access the cord reel
  • Once you have access to the cord reel, you can try winding the cord back onto it
  • If the cord is very loose, you may need to replace the cord reel
  • If the cord is still stuck, you may need to replace the starter assembly

How to Replace a Pull String on a Push Mower

How to fix lawn mower pull cord stuck

If you’re like most people, you rely on your lawn mower to keep your lawn looking neat and tidy. But what do you do when the pull cord on your lawn mower gets stuck?

First, try to identify the problem. Is the cord stuck on the spool? Or is it jammed in the housing? If the cord is stuck on the spool, the easiest way to fix it is to simply wind it back onto the spool.

To do this, you’ll need to remove the spark plug wire so the engine can’t start accidentally. Then, use your hands to wind the cord around the spool in the opposite direction that it unwinds. If the cord is jammed in the housing, you’ll need to use a pair of pliers to carefully pull it out.

Be careful not to damage the cord as you do this. Once you’ve identified and fixed the problem, reattach the spark plug wire and you should be good to go!

How do you fix a pull string on a lawn mower?

If you’re a lawn mower owner, chances are you’ve had to deal with a broken or frayed pull string. While it may seem like a daunting task, fixing a pull string on a lawn mower is actually quite simple.

Here’s a step-by-step guide on how to do it:

1. Start by removing the spark plug from the lawn mower. This will prevent the engine from accidentally starting while you’re working on it.

2. Next, locate the pull string housing. This is usually located near the bottom of the lawn mower’s engine.

3. Once you’ve found the pull string housing, use a screwdriver to remove the screws that hold it in place.

4. With the housing removed, you should be able to see the pull string itself. If the string is frayed or broken, simply cut it off and discard it.

5. To replace the pull string, thread a length of strong rope or string through the housing and tie a knot at the end. Make sure the string is long enough so that you can easily pull it when starting the lawn mower.

6. Once the new string is in place, simply reattach the housing and screw it back into place.

7. Finally, reattach the spark plug and you’re ready to go!

With these simple steps, you can easily fix a broken or frayed pull string on your lawn mower.

How do you fix a pull cord on a lawn mower that won’t retract?

If the pull cord on your lawn mower is not retracting, there are a few things you can do to fix it. First, check to see if the cord is tangled. If it is, you will need to untangle it.

Be careful not to pull too hard, as this can damage the cord. Once the cord is untangled, try pulling it again. If it still does not retract, there may be something blocking the way.

Check to see if there is any dirt or debris caught in the mechanism. If there is, clear it away and try again. If the cord still will not retract, the problem may be with the spring.

over time, the spring can become weak and may need to be replaced. This is a more difficult repair, and you may need to take your lawn mower to a professional to have it done. No matter what the problem is, with a little troubleshooting you should be able to get your lawn mower’s pull cord working again.

How do you reattach a pull cord?

Assuming you are referring to a pull cord on a small engine (lawn mower, leaf blower, etc.), the process is actually quite simple. First, you will need to locate the point where the cord broke. If the cord is frayed, you will need to cut off the frayed end before proceeding.

Next, thread the end of the cord through the recoil assembly. Make sure you leave enough cord to comfortably grip, then tie a knot in the end. Finally, pull the cord to tighten, and you should be all set!

What does it mean when your lawn mower cord won’t pull?

There are a few things that could be going on if your lawn mower cord won’t pull. The first thing you should check is to see if the cord is tangled or kinked. If it is, you’ll need to straighten it out before you can continue.

Another possibility is that the cord is just old and needs to be replaced. If you’ve had your lawn mower for a while, it’s possible that the cord has just worn out and isn’t as strong as it used to be. In this case, you’ll need to buy a new cord.

Finally, it’s possible that there’s something wrong with the lawn mower itself. If you’ve checked the cord and it doesn’t seem to be the problem, it’s worth taking your lawn mower to a professional to have it checked out.

Conclusion

If the lawn mower pull cord is broken, it can be a real pain to fix. Here are some steps to take to fix a broken lawn mower pull cord. By following the tips in the above you should be able to pull the cord and start the lawn mower.